Ritron OUTPOST Series Informações Técnicas descarregar pdf (Página 16)

OUTPOST Wireless Callbox PC Programming

2-T

ONE

ECODE

ECEIVE

) S

ETTINGS

.....................................

2-Tone decode can be used to selectively call the

Callbox in a system where multiple radios operate on

a single frequency. Alternatively, 2-Tone decode can

also be used to operate the Switch Output built into

every Callbox.

When the radio is programmed for 2-Tone Paging de-

code, no call will be heard unless the 2-tone code has

been successfully decoded or the On/PTT button has

been pressed. After decoding, normal 2-way conver-

sation is possible without the need for the 2-tone code.

2-Tone Paging Decode is automatically reset when

the RQX Reset Time expires.

When the Callbox is programmed for Switch Output

operation with 2-Tone decode, regular voice commu-

nication is unaffected by the 2-tone code. If the Switch

Output Option uses 2-tone decode it cannot be used

for 2-Tone Paging Decode.

2-Tone Table #

The OUTPOST™ Calbox comes equipped with 9 pre-

determined 2-Tone codes that correspond to table

codes that certain RITRON portable and base radios

can send. Use of the 2-Tone Table codes allows pro-

gramming without the need for the PC programmer.

1st Tone decoded for 1 sec.

You can custom program the 1

tone of the 2-tone

code to any frequency between 300-1500 Hz. The 1st

tone must be decoded for the programmed period of

time before the radio looks for the 2nd tone.

2nd Tone decoded for 1 sec.

You can custom program the 2nd tone of the 2-tone

code to any frequency between 300-1500 Hz.The 2nd

tone must be decoded for the programmed period of

time after the 1st tone has been decoded.

All Call decoded for 1 sec.

With 2-Tone All Call enabled you can custom program

an All Call tone to any frequency between 300-1500

Hz. The All Call tone must be decoded for the pro-

grammed period of time.

Ring Tone Enable

With this feature enabled the Callbox will sound a ring

signal in the speaker, similar to a telephone ring, any

time the 2-Tone code, Group Call or All Call code is

decoded.

2-Tone Transpond

2-Tone Transpond transmits a tone after the 2-Tone

code, Group Call or All Call code has been received to

alert the calling radio that the 2-Tone code was suc-

cessfully decoded.

2-Tone Group Call

When this option is set, 2-tone decode is achieved if

the radio receives the 1st tone for the programmed All

Call time. If this option is selected the All Call time

must be longer than the 1st Tone time or the Callbox

will always decode on the 1st tone, ignoring the 2nd

tone altogether.

2-Tone Monitor Trip

With this option selected the Callbox will be in carrier

squelch mode any time the 2-Tone code is decoded,

regardless of any QC or DQC code programmed in

the radio. The radio reverts back to tone code decode

if the ON/PTT button is pressed and reverts back to

2-tone decode after the RQX Reset Time has expired.

Turn-Off Code

In certain Switch Output applications a separate 2-

tone turn-off code is required. This code can not be

the same as the 2-Tone Code

NTERCOM

LWAYS

) P

ROGRAMMING

..............................

The XT OUTPOST™ can be PC programmed to

operate as a two-way intercom. When operating as an

intercom the Automatic Turn-Off is disabled and the

radio will remain on in a “stand-by” mode, allowing it

to receive a call from another radio at any time. The

higher current requirements of Intercom operation

make it undesirable in battery powered installations.

Required Programming:

Automatic Turn-Off

This must be disabled for the Callbox to remain turned

on at all times.

Optional Programming:

Battery Saver

Battery Saver can be used to reduce battery drain on

a battery powered installation. With Battery Saver

activated, the Callbox will periodically “wake-up” and

listen for a received signal before returning to a low

current “sleep” state. The time between “wake-up’

states can be PC programmed between 0.5 - 8 sec-

onds. A longer time between “Wake-up” states will re-

sult in increased battery life.

Busy Channel TX Inhibit

This will not allow you to transmit when another user is

already transmitting on your radio frequency, even if

they are using a different tone code. The radio will

beep a series of long, low tones while the ON/PTT

button is held down (like a busy signal). When the

Callbox is programmed for 2-Tone paging Decode,

or is used in a system with multiple QC or DQC codes,

this prevents the Callbox from interfering with other

users on the radio channel.

14 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22

Comentários a estes Manuais

Sem comentários

Ritron OUTPOST Series Informações Técnicas Página 16

Comentários a estes Manuais

Manuais e produtos relacionados com Rádios bidirecionais Ritron OUTPOST Series